Instructions For Ten. Abr. TA-H70 Series Stone Set

TNABR TA-H70 Series Stone Set consists of one (1) pair of Stone Assemblies and one (1) pair of Guides. Stone Assemblies and Guides may be changed WITHOUT removing Master Holders from Hone Head Module.

Instructions For Ten. Abr. TA-H50 Series Stone Set

TNAbr. TA-H50 Series Stone Sets consist of one (1) pair of Stone Assemblies. Stone Assemblies may be changed WITHOUT removing Master Holders from Hone Head Module.

H70-H50 A 5 7
SERIES ABRASIVE TYPE GRIT SIZE HARDNESS
ABRASIVE TYPES
A – ALUMINUM OXIDE
C, J – SILICON CARBIDE
DM, DR, DV – DIAMOND
NM, NR – CBN
R25 – RUBY A/O
QT25 – CUBITRON
WA – PURE A/O
GRIT SIZE
1- 70 8- 400
2- 80 9- 500
3- 100 0- 600
4- 150 80- 800
5- 220 90- 900
6- 280 10- 1000
7- 320 00- 1200
HARDNESS
1- SOFT
3-
5-
7-
9-
11-
13-
15- HARD
Approximate Surface Finish in Micrometers (μm) Ra
MATERIAL ABRASIVE TYPE GRIT SIZE
80 100 150 220 280 320 400 500 600 1200
Hard Steel Aluminum Oxide/Silicon Carbide 0,65 0,50 0,45 0,30 0,25 0,12 0,08 0,03
CBN 1,40*2,00 1,15 1,00 0,70 0,50 0,18 0,05
Soft Steel Aluminum Oxide/Silicon Carbide 2,00 0,90*1,40 0,65 0,50*0,90 0,40 0,18*0,25 0,10*0,20 0,05
CBN 1,60*2,50 1,25*2,00 0,65 0,40 0,12
Cast Iron Silicon Carbide 2,50 0,75*1,00 0,50 0,30 0,25 0,15 0,12 0,08
Diamond 2,00 1,27 0,50 0,30
Aluminum, Brass, Bronze Silicon Carbide 4,30 2,00 1,40 0,85 0,70 0,40 0,30 0,05
Carbide Diamond 0,75 0,50 0,18 0,08 0,03
Ceramic Diamond 1,27 1,00 0,50 0,40 0,25
Glass Diamond 2,40 1,80 0,75 0,40 0,20

Surface Finish Conversions: Millimeter to Inch – To convert one unit of measure to the other use the following formulas. Micrometer to microinch: Micrometer x 40 = Microinch

Formulas for determining minimum stock removal required on diameter to achieve desired surface finish. Surface Finish in Micrometers – (μm) Ra

EXISTING FINISH – DESIRED FINISH
100,000
= REQUIRED
STOCK REMOVAL

Example: Existing Finish = 50 μm”; Desired Finish = 10 μm”

50 – 10
100,000
= 0.0004 INCH
Approximate Surface Finish in Microinches (μ in) Ra
MATERIAL ABRASIVE TYPE GRIT SIZE
80 100 150 220 280 320 400 500 600 1200
Hard Steel Aluminum Oxide/Silicon Carbide 25 20 18 12 10 5 3 1
CBN 55*80 45 40 28 20 7 2
Soft Steel Aluminum Oxide/Silicon Carbide 80 35*55 25 20*35 16 7*10 4*8 2
CBN 65*100 50*80 25 16 5
Cast Iron Silicon Carbide 100 30*40 20 12 10 6 5 3
Diamond 80 50 20 12
Aluminum, Brass, Bronze Silicon Carbide 170 80 55 33 27 16 12 2
Carbide Diamond 30 20 7 3 1
Ceramic Diamond 50 40 20 15 10
Glass Diamond 95 70 30 15 8

Surface Finish Conversions: Inch to Millimeter – To convert one unit of measure to the other use the following formulas. Microinch to micrometer: Microinch ÷ 40 = Micrometer

*If two values are shown: the first number is for the small parts, honed on machines with one horsepower or less; the second number is for large parts, honed on machines with two or more horsepower

Formulas for determining minimum stock removal required on diameter to achieve desired surface finish. Surface Finish in Microinches – (μ”) Ra

EXISTING FINISH – DESIRED FINISH
100,000
= REQUIRED
STOCK REMOVAL

Example: Existing Finish = 50 μm”; Desired Finish = 10 μm”

50 – 10
100,000
= 0.0004 INCH